rs=w-1440,h-1440.jpeg
52415904_1382888435179775_36206223792998

HEAVY DUTY GROUND STABILISING SLABS

ALWAYS ADAPTABLE TO YOUR NEEDS

83648556_2560788170804196_43589526407390

MINIMAL GROUND PREPARATION

HIGHLY DURABLE AND VERY STRONG

46804798_2658030014208976_33377242351109
80406176_3775450622466904_27287915157100

ENGINEERED TO BE SLIP RESISTENT

ENABLE NATURAL SURFACE DRAINAGE

WHY CHOOSE
MUDCONTROL INB® SLABS?

--2_edited.jpg

PRICING

£23 per square metre excluding VAT

£27.60 including VAT

DELIVERY

Why aren't your delivery costs on the website? 

The cost per pallet varies depending on the delivery postcode. It also varies a tiny bit depending on the weight of the pallet. So we do a ‘pallet preparation and delivery’ quotation individually for every enquiry. 

MUDCONTROL INB® Slabs are fully certified - please see our array of certificates here

INSTALLING YOUR MUDCONTROL INB SLABS

 

FITTING AND CUTTING

The second row of slabs should be staggered against the first by using a half grid at the beginning. Slabs can be easily cut with a saw.  

 

MUDCONTROL INB® slabs are easily cut with circular saws, bench saws, panel saws or jig saws. Other power tools may also be appropriate. 

PREPARATION

Level the ground by flattening bumps, removing rocks and filling holes. Lay down the first row of MUDCONTROL INB® slabs across the full length of the area to be covered.

INSERTING

When laying down MUDCONTROL INB® slabs, a crowbar or shovel can give helpful leverage - but do not apply too much force. The slabs should fit loosely together to avoid high tensions during extreme hot or cold weather.

 

Lay down the second row of slabs after the first row has been done. Remember to leave a 1/4” (0.5 cm) expansion gap. Our MUDCONTROL INB® slabs make it easy to cover even large areas relatively quickly. Although the grids adapt well to uneven ground, level ground gets the best results. 

FITTING TIPS

It is best to cover exposed locating tabs to avoid damage from movement over the leading edge this can be done with soil, sand or a similar medium.

 

A substrate like sand can be used to level the slabs out. Even after installation, substrate can fill gaps and dips by using a leverage action.

FINISHING

Once the slabs have been laid out, cover with sand or another water-permeable material.  If you are using the slabs for livestock use, please use washed fine/soft sand or QUARRIED SHARP SAND - visit our SAND INFORMATION page for more info.  

REMOVING AND RE-LAYING THE SLABS

Care should be taken when lifting the slabs for re-use, by far the best way to do this is by lifting the leading edge by about 15cm (6 inches) one row at-a-time and pull the lifted row away from the connecting row horizontally, lifting the slabs by more than 15 degrees can cause undue stress on the locating tabs and cause them to break, which will not generally be covered by the manufacturer’s warranty.

Please allow any Animals / Livestock time to acclimatise to any changes in ground surfaces.  Once the slabs have been laid, we recommend filling the holes with sand or another water permeable material. For general use, but especially with all-season open stabling, we recommend a finishing layer of sand, as per the manufacturer's installation instructions.


Please be aware in certain circumstances of extremely waterlogged ground and where liquid mud is on the surface, the mud will come up through the holes in the slabs, this is normal. You may need to scrape this off the surface, the same is true of mud carried onto the surface by traffic. The slabs will still provide a stable platform and stop you sinking in the mud.

If you are ready for a no-obligation quote or want to contact us for more information, then please use the button below - we are here to help.

MUDCONTROL - BELIEVE THE HYPE

Want to know more?  Check out our Facebook & YouTube channels.

Looking for Mudcontrol INB® slab installation instructions? Click HERE

  • Facebook
  • YouTube

©2019 by Mudcontrol Ltd.  Designed by WeezyLambDesign